1. Spoiler

   Click at the bottom edge of the screen to look at the floor.

2. Spoiler

   A little above the dead center there's a crack, go ahead and click on it to reveal a hole.

3. Spoiler

   Pick up the screwdriver and the empty glass. Both are kind of hidden and may be hard to see. The screwdriver is off to the left, the empty glass is up top and to the right. Click off to the left side of the screen to get a view of the Enertron.

4. Spoiler

   Pick up the Kettle. You'll notice in the window to the right, the back wall has some meandering lines on it. Click on it to get part of the circuit board. Go left.

5. Spoiler

   Use the screwdriver on each of the four corners of the metal plate on the wall. Get the circular remote control and the two power cells.

6. Spoiler

   Same view off to the left there is a faucet. There is a clickable blue tile at the head of the faucet, click it to get another piece of the circuit board.

7. Spoiler

   Click on the faucet to turn it on and use the kettle on the faucet.

8. Spoiler

   Open the cabinet beneath the sink. Make a note of the written numbers and symbols but for now click the darker square at the bottom of the cupboard to get the third circuitboard tile.

9. Spoiler

   There is a hotspot where the green wallpaper meets the white a little higher than halfway down. Click on it to reveal a three digit number.

10. Spoiler

    The number will be 534. Now with this in mind and the translation in the cupboard beneath the sink, click on the canister in the right hand corner with the biohazard symbol on it.

11. Spoiler

    Enter in the translated code, from left to right you should have to click the buttons: four times, two times, three times. Now click on the button off to the right to open the canister.

12. Spoiler

    Click on the frozen embryo and click off to the side to zoom out.

13. Spoiler

    Go left.

14. Spoiler

    Use the circuit tiles on the brown bars so that they are all lined up vertically. From here our job is to place the circuit board tiles in the correct positions on the square block to the left.

15. Spoiler

    Numbering the tiles 1-4, they should go in the following positions. 1:bottom left 2: top right 3: top left 4: bottom right.

16. Spoiler

    With the tiles in the correct positions, click on the yellow button with the black lightning bolt symbol.

17. Spoiler

    Turn all the way around to face the enerton.

18. Spoiler

    Place the frozen embryo in the left hand window and one of the power cells in the right hand window, click the green button and when the process finishes, take both out again.

19. Spoiler

    Place the kettle back on the docking bay you took it from and use the glass on the kettle. Now place the glass full of hot water on the left hand enerton window, and the other depleted power cell on the right hand window. When the process is complete, remove the power cell and turn right to look at the sphere (you don't need the water glass anymore.

20. Spoiler

    Click on the circular remote control in your inventory to make it visible.

21. Spoiler

    Click on the top button (v shaped symbol) to open the iris.

22. Spoiler

    Place the cold power cell in the opened iris, and click the top button again to close the iris.

23. Spoiler

    Click the left most button (looks like a zero) to make the sphere float and extend its legs.

24. Spoiler

    Click the bottom button (shaped sort of like a cursive lower case a) to extend the robot's head.

25. Spoiler

    Now click the top button to open the iris, remove the cold cell, and insert the heated cell. Click the top button again to close the iris, and turn all the way around to face the portion of the room with the sink.

26. Spoiler

    Click on the giant screw until it is in its highest position.

27. Spoiler

    Use the cold core on the top of the screw. Click the right most button on the remote control. When the process is finished, take the now supercharged power cell and turn around to face the sphere.

28. Spoiler

    Click the top button on the remote, remove the power cell and replace it with the super charged power cell and click the top button again to close the iris.

29. Spoiler

    Click the middle button on the remote and wait for the process to finish.

30. Spoiler

    Click on the gaping black hole and you are finished! Congratulations!

Material collection

The ENERTRON

The sphere